English
Français
Pусский
Español
Deutsch
Italiano
한국어
Tiếng Việt
ไทย
ភាសាខ្មែរ
Filipino
Bahasa indonesia
हिन्दी
简体中文
You are here: Home » Media Center » News » How to use Crawler impact crushing station?

How to use Crawler impact crushing station?

Publish Time: 2021-10-25     Origin: Site

The crawler impact crushing station can effectively remove the dust system, suitable for diesel engine noise and sewage conditions, the release system can remotely control the hydraulic pressure to remove obstacles in the mobile crushing station, and the pre-screening device greatly improves the crushing efficiency.


What are the steps to use the crawler impact crushing station?

How to install a crawler impact crushing station?

What are the functions of the crawler mobile crushing station?



What are the steps to use the crawler impact crushing station?

1. When the crawler impact crushing station is installed and connected with the hydraulic excavator or other construction machinery, the working pressure and flow rate of the main machine hydraulic system must meet the technical parameter requirements of the crawler impact crushing station, and the "p" port of the crawler impact crushing station is connected to the main engine high-pressure oil circuit Connect, the "a" port is connected with the return line of the main engine.

2. The best hydraulic oil temperature when the crawler impact crushing station is working is 50-60 degrees, and the maximum should not exceed 80 degrees. Otherwise, the load of the crawler impact crushing station should be reduced.

3. The working medium used by the crawler impact crushing station can usually be the same as the oil used in the main engine's hydraulic system. It is recommended to use yb-n46 or yb-n68 anti-wear hydraulic oil in general areas, and yc-n46 or yc-n68 low-temperature hydraulic oil in cold areas. The filtration accuracy of hydraulic oil is not less than 50 micro m.

4. New and repaired crawler impact crushing stations must be refilled with nitrogen when they are activated, with a pressure of 2.5 ±0.5mpa.

5. Calcium-based grease or compound calcium-based grease must be used for lubrication between the handle of the drill rod and the guide sleeve of the cylinder, and it should be refilled once per shift.

6. When the crawler impact crushing station is working, the drill rod must be pressed on the rock first, and the breaker must be started after maintaining a certain pressure. It is not allowed to start in the suspended state.


How to install a crawler impact crushing station?

1. The equipment should be installed on a level concrete foundation and fixed with anchor bolts.

2. Pay attention to the verticality between the main body and the horizontal when installing.

3. After installation, check whether the bolts at various parts are loose and whether the door of the main engine is fastened. If so, please fasten it.

4. Configure the power cord and control switch according to the power of the crawler impact crushing station.

5. After the inspection is completed, carry out a no-load test run, and the test run can be carried out normally.


What are the functions of the crawler mobile crushing station?

1. Mobile screening and crushing equipment has the characteristics of multi-functional operation;

2. It is widely used in the coarse crushing of hard materials in mining sites in mines, coal mines, and cement industries;

3. Recycling of construction waste, earthwork works, urban infrastructure, roads or construction sites, and other site operations;

4. Treatment of surface soil and various other materials; separation of viscous concrete aggregates; construction and blasting industries; screening after crushing;

5. Stripping crushing for cement concrete road reconstruction, crushing of asphalt concrete before regeneration.


The crawler mobile crushing station has been widely used in infrastructure construction, mining, construction, and other fields, helping people to achieve a significant increase in production efficiency. Sunward, the pioneer in producing crawler impact crushing stations in China, knows that every application is special. Their knowledgeable employees can find the best solution for each scenario, especially when customized products are required.


Here You Can Leave Comments And Suggestions To Us Here
Sunward Intelligent Equipment Group (hereinafter referred to as "SUNWARD") was founded in 1999, led by Professor He Qinghua of Central South University.

CONTACT US

 E-mali:  international@sunward.cc 
Add: Sunward Industrial Park, No. 1335 Liangtang Road (E), Xingsha, Changsha, Hunan, China
  Tel: +86-400-887-6230
 Complaint Mailbox: jubao@sunward.com.cn ( For report vilations or illegal actions only)
Copyright © 2024 Sunward Intelligent Equipment Group. All Rights Reserved.  | Sitemap | Privacy Policy